Change transmission fluid every 30,000 miles. Most owner’s manuals say it isn’t necessary. Yeah, right. That’s why transmission shops are making a fortune replacing burned out automatic transmissions. For optimum protection, change the Transmission Fluid and filter every 30,000 miles (unless you have a new vehicle that is filled with Dexron III ATF, which is supposed to be good for 100,000 miles).
An automatic transmission creates a lot of internal heat through friction: the friction of the fluid churning inside the torque converter, friction created when the clutch plates engage, and the normal friction created by gears and bearings carrying their loads.
It doesn’t take long for the automatic transmission fluid (ATF) to heat up once the vehicle is in motion. Normal driving will raise fluid temperatures to 175 degrees F., which is the usual temperature range at which most fluids are designed to operate. If fluid temperatures can be held to 175 degrees F., ATF will last almost indefinitely — say up to 100,000 miles. But if the fluid temperature goes much higher, the life of the fluid begins to plummet. The problem is even normal driving can push fluid temperatures well beyond safe limits. And once that happens, the trouble begins.
At elevated operating temperatures, ATF oxidizes, turns brown and takes on a smell like burnt toast. As heat destroys the fluid’s lubricating qualities and friction characteristics, varnish begins to form on internal parts (such as the valve body) which interferes with the operation of the transmission. If the temperature gets above 250 degrees F., rubber seals begin to harden, which leads to leaks and pressure losses. At higher temperatures the transmission begins to slip, which only aggravates overheating even more. Eventually the clutches burn out and the transmission calls it quits. The only way to repair the damage now is with an overhaul — a job which can easily run upwards of $1500 on a late model front-wheel drive car or minivan.
As a rule of thumb, every 20 degree increase in operating temperature above 175 degrees F. cuts the life of the fluid in half!
At 195 degrees F., for instance, fluid life is reduced to 50,000 miles. At 220 degrees, which is commonly encountered in many transmissions, the fluid is only good for about 25,000 miles. At 240 degrees F., the fluid won’t go much over 10,000 miles. Add another 20 degrees, and life expectancy drops to 5,000 miles. Go to 295 or 300 degrees F., and 1,000 to 1,500 miles is about all you’ll get before the transmission burns up.
If you think this is propaganda put forth by the suppliers of ATF to sell more fluid, think again. According to the Automatic Transmission Rebuilders Association, 90% of ALL transmission failures are caused by overheating. And most of these can be blamed on worn out fluid that should have been replaced.
On most vehicles, the automatic transmission fluid is cooled by a small heat exchanger inside the bottom or end tank of the radiator. Hot ATF from the transmission circulates through a short loop of pipe and is thus “cooled.” Cooling is a relative term here, however, because the radiator itself may be running at anywhere from 180 to 220 degrees F.!
Tests have shown that the typical original equipment oil cooler is marginal at best. ATF that enters the radiator cooler at 300 degrees F. leaves at 240 to 270 degrees F., which is only a 10 to 20% drop in temperature, and is nowhere good enough for extended fluid life.
Any number of things can push ATF temperatures beyond the system’s ability to maintain safe limits: towing a trailer, mountain driving, driving at sustained high speeds during hot weather, stop-and-go driving in city traffic, “rocking” an automatic transmission from drive to reverse to free a tire from mud or snow, etc. Problems in the cooling system itself such as a low coolant level, a defective cooling fan, fan clutch, thermostat or water pump, an obstructed radiator, etc., will also diminish ATF cooling efficiency. In some cases, transmission overheating can even lead to engine coolant overheating! That’s why there’s a good demand for auxiliary add-on transmission coolers.
An auxiliary transmission fluid cooler is easy to install and can substantially lower fluid operating temperatures. The plate/fin type cooler is somewhat more efficient than the tube and fin design, but either can lower fluid temperatures anywhere from 80 to 140 degrees when installed in series with the stock unit. Typical cooling efficiencies run in the 35 to 50% range.
What kind of automatic transmission fluid should you use in your transmission? The type specified in your owner’s manual or printed on the transmission dipstick.
For older Ford automatics and certain imports, Type “F” is usually required. Most Fords since the 1980s require “Mercon” fluid, which is Ford’s equivalent of Dexron II.
For General Motors, Chrysler and other imports, Dexron II is usually specified.
NOTE: Some newer vehicles with electronically-controlled transmissions require Dexron IIe or Dexron III fluid. GM says its new long-life Dexron III fluid can be substituted for Dexron II in older vehicle applications.
CAUTION: Using the wrong type of fluid can affect the way the transmission shifts and feels. Using Type F fluid in an application that calls for Dexron II may make the transmission shift too harshly. Using Dexron II in a transmission that requires Type F may allow the transmission to slip under heavy load, which can accelerate clutch wear.
It’s a messy job because there’s no drain plug to change the fluid, but you can do it yourself if you’re so inclined. To change the fluid, you have to get under your vehicle and remove the pan from the bottom of the transmission.
When you loosen the pan, fluid will start to dribble out in all directions so you need a fairly large catch pan. You should also know that removing the pan doesn’t drain all of the old fluid out of the transmission. Approximately a third of the old fluid will still be in the torque converter. There’s no drain plug on the converter so you’re really only doing a partial fluid change. Even so, a partial fluid change is better than no fluid change at all.
A typical fluid change will require anywhere from 3 to 6 quarts of ATF depending on the application, a new filter and a pan gasket (or RTV sealer) for the transmission pan. The pan must be thoroughly cleaned prior to reinstallation. This includes wiping all fluid residue from the inside of the pan and scraping all traces of the old gasket from the pan’s sealing surface. Don’t forget to clean the mounting flange on the transmission, too.
When the new filter is installed, be sure it is mounted in the exact same position as the original and that any O-rings or other gaskets have been properly positioned prior to tightening the bolts. Then tighten the bolts to the manufacturer’s recommended specs.
When refilling the transmission with fresh fluid, be careful not to allow any dirt or debris to enter the dipstick tube. Using a long-neck funnel with a built-in screen is recommended.
CAUTION: Do not overfill the transmission. Too much fluid can cause the fluid to foam, which in turn can lead to erratic shifting, oil starvation and transmission damage. Too much fluid may also force ATF to leak past the transmission seals.
Add half a quart at a time until the dipstick shows full. The transmission really isn’t full yet because the dipstick should be checked when the fluid is hot, and the engine is idling with the gear selector in Park. So start the engine, drive the vehicle around the block, then recheck the fluid level while the engine is idling and add fluid as needed until the dipstick reads full.
Check and/or change your Air Filter every 6 months to improve fuel economy and keep your engine running smoothly.
Most car batteries today are maintenance-free, sealed and can last more than three years. The first sign your battery should be replaced is often trouble starting the engine
Have your antifreeze fluid changed and Cooling System flushed every 30,000 miles or 2 years. Newer formulas, however, may last up to 50,000 miles.
Schedule a complete and Engine Diagnostics (Professional Maintenance) check every 15, 30, 60, and 90,000 miles.
Take 10 minutes and use our Monthly Checklist to do your own quick visual car inspection and fluid levels check.
Tire rotation or rotating tires is the the practice of moving automobile wheels and tires from one position on the car to another, to ensure even tire wear.
Have your Wheel Alignment checked every other tire rotation and always when installing new tires. Wheel alignment sometimes referred to as tracking, is part of standard automobile maintenance
Joe’s Tires proudly serves the local Berkeley, CA area. We understand that getting your car fixed or buying new tires can be overwhelming. Let us help you choose from our large selection of Tires.
Tito was awesome. Got my company car in and out for a reasonable price and he communicated well. He made sure I got what I needed (tires and alignment) and… read more didn’t try to fluff the service or price up. Solid place for business. I will be listing this place as my companies go to for service.
Tesla had failed me and my alignment was severely off resulting in my tire wear being very uneven.
No fear because Joe’s Tires fixed it well within the allotted… read more estimate time (just over an hour vs the est. 2 hours). I even had to cut my coffee time short because they were so quick, which, as an added bonus there are tons of shops and restaurants around the area to hang out at while you wait.
My air pressure light came on again a couple days after I had filled the tires due to my front right tire being low. After re-checking, I realized the… read more tire must have a leak. I drive into Joe’s Tires straight from summer camp pick up after a very short search for places nearby– shortly after 4pm. I expected to have to make an appointment for the next day or later in the week and also assumed I would need to replace the tire. To my surprise and delight, I was helped right away. They took the car and said it would probably be about an hour. 15 minutes later they called to say it was a simple fix– a screw had punctured the tire and they plugged the hole and patched it up. $35 and 15 minutes?? Amazing. They have my business for our two family cars for life!! Friendly, fast, fair.
Definitely the most wonderful tire experience ever! I know nothing about tires but my mechanic said I needed new front tires and recommended Joe’s…I called and they scheduled an… read more appointment for the next day. In addition to ordering the correct tires, they discovered I had a bent rim and bad tire on the back. They got the rim repaired and did an alignment. OMG…what a difference in driving that made. Every single person I dealt with was just wonderful and I am very grateful to have this place as a resource for the future. I would give it 10 stars!
I remember calling Ken Betts Chevron Service Center asking if I could get my 2001 BMW 740iL in for an alignment. He said that the best person he can recommend… read more is Joe’s Tires. Amazing service and was detailed on what I needed and what could use an adjustment. They are really good with their work car felt amazing and did it quickly than expected. Thanks again! Will becoming here again and telling people about this spot.